H&R TRAK+ DRA Bolt-On Wheel Spacers 30-45mm (Pair) - Porsche 911 991/992 Carrera / 996 / 997 / Boxster / Cayman 5x130

Sale price $206.96 Regular price $229.95

Black Friday price: $196.61 (applied in cart)

SKU: 60957160

Add To Wishlist

Big offset changes on a 911 or a Boxster call for a spacer that does more than fill a gap. At 30mm and wider per side, H&R uses its DRA bolt-on design. The spacer bolts to your hub with special bolts H&R includes, and the wheel then mounts to the spacer with your factory wheel bolts.

That means no hunting for extra-long wheel bolts. The DRA keeps the 5x130 bolt pattern and 71.6mm center bore, and it is hubcentric on both the hub and the wheel side. Choose your width and finish above. The 40mm and 45mm spacers come in silver only. Each kit is a pair for one axle.

Why H&R TRAK+ DRA Bolt-On Spacers

TRAK+ spacers are made from a proprietary alloy that H&R developed for them. H&R rates it lighter and stronger in tensile strength than 6061-T6 billet aluminum. Each spacer has full contact with the hub face, just like the factory hub, so the load spreads evenly instead of riding on a thin ring.

Check your factory wheel bolts before you order. They thread into the spacer, so they must not be so long that the tip reaches the hub face. Measure yours, or send us a photo of a bolt next to a ruler and we will confirm.

What's Included

  • 2 H&R TRAK+ DRA spacers in the width and finish you choose (one axle)
  • Special hub bolts to mount the spacers

Product photo shows a representative H&R TRAK+ DRA spacer. Width, finish and packaging vary by option.

Key Features

  • Widths of 30mm, 35mm, 40mm and 45mm per side
  • Bolt-on design, special hub bolts included
  • Wheel mounts to the spacer with your factory wheel bolts
  • Silver or black finish on 30mm and 35mm, silver on 40mm and 45mm
  • Fits the 5x130 bolt pattern with a 71.6mm center bore
  • Hubcentric on both the hub and wheel side
  • Made in Germany
  • Sold as a pair. Order two pairs for all four corners.

Vehicle Fitment and Available Widths

The H&R TRAK+ DRA spacers in this listing fit these models:

  • Porsche 992 911 Carrera / Carrera S Coupe and Cabriolet (2020-2026), Carrera 4 (2020-2024), Carrera 4S (2020-2026): 30mm, 35mm, 40mm and 45mm
  • Porsche 991 911 Carrera / Carrera S (2012-2019), Carrera 4 / 4S (2013-2019), Carrera GTS (2015-2019), Turbo / Turbo S (2014-2019): 30mm, 35mm, 40mm and 45mm
  • Porsche 997 911 Carrera / Carrera S / Carrera 4 / Carrera 4S / Turbo (2005-2012): 30mm, 35mm, 40mm and 45mm
  • Porsche 996 911 Carrera / Carrera 4 / Carrera 4S / Turbo (1999-2005): 30mm, 35mm, 40mm and 45mm
  • Porsche 981 Cayman / Cayman S (2014-2016): 30mm, 35mm, 40mm and 45mm
  • Porsche 987 Boxster / Boxster S (2005-2012), Boxster Spyder (2011), 987 Cayman / Cayman S (2006-2012): 30mm, 35mm, 40mm and 45mm
  • Porsche 986 Boxster / Boxster S (1997-2004): 30mm, 35mm, 40mm and 45mm

H&R lists these widths for each model. Not sure about your car? Send us your VIN and we will confirm before you order.

Installation Notes

A DRA install has two steps at each corner: the spacer bolts to the hub, then the wheel bolts to the spacer. Use a torque wrench for both. Professional installation is recommended. At these widths, check fender and suspension clearance with your exact wheel and tire before you drive.

  1. Clean the hub face and remove any rust or scale so the spacer sits flat.
  2. Bolt the DRA spacer to the hub with the special bolts supplied, tightened to the torque in the H&R instructions.
  3. Check that your factory wheel bolts are not long enough to reach the hub face once threaded into the spacer.
  4. Mount the wheel on the spacer and tighten the factory wheel bolts to factory torque in a star pattern.
  5. Turn the wheel by hand and check that nothing rubs. The wheel should spin freely.
  6. Re-check the torque on the spacer bolts and wheel bolts after the first short drive.