H&R TRAK+ DRA Bolt-On Wheel Spacers 25-30mm (Pair) - BMW F-Series 5x120 (F10, F30, F32, F80 M3, F82 M4)

Sale price $188.96 Regular price $209.95

Black Friday price: $179.51 (applied in cart)

SKU: 50757254

Add To Wishlist

Running high-offset wheels on an F-series BMW, 25mm to 30mm per side is often where the wheel finally lines up with the fender. At that width H&R uses its DRA bolt-on design. The spacer bolts to your hub with special bolts H&R includes, and the wheel then mounts to the spacer with your factory wheel bolts.

That means no hunting for extra-long wheel bolts. The DRA keeps the 5x120 bolt pattern and 72.5mm center bore, and it is hubcentric on both the hub and the wheel side. Choose your width and finish above. Each kit is a pair for one axle.

Why H&R TRAK+ DRA Bolt-On Spacers

TRAK+ spacers are made from a proprietary alloy that H&R developed for them. H&R rates it lighter and stronger in tensile strength than 6061-T6 billet aluminum. Each spacer has full contact with the hub face, just like the factory hub, so the load spreads evenly.

Check your factory wheel bolts before you order. They thread into the spacer, so they must not be so long that the tip reaches the hub face. Measure yours, or send us a photo of a bolt next to a ruler and we will confirm.

What's Included

  • 2 H&R TRAK+ DRA spacers in the width and finish you choose (one axle)
  • Special hub bolts to mount the spacers

Product photo shows a representative H&R TRAK+ DRA spacer. Width, finish and packaging vary by option.

Key Features

  • Widths of 25mm and 30mm per side
  • Bolt-on design, special hub bolts included
  • Wheel mounts to the spacer with your factory wheel bolts
  • Silver or black finish
  • Fits the 5x120 bolt pattern with a 72.5mm center bore
  • Hubcentric on both the hub and wheel side
  • Made in Germany
  • Sold as a pair. Order two pairs for all four corners.

Vehicle Fitment and Available Widths

The H&R TRAK+ DRA spacers in this listing fit these models:

  • BMW F22 228i / 230i / M235i / M240i Coupe, incl. M235i / M240i xDrive (2014-2021): 25mm and 30mm
  • BMW F23 228i / 230i / M235i / M240i Convertible (2015-2021): 25mm and 30mm
  • BMW F30 320i / 328i / 330i / 335i / 340i Sedan, incl. xDrive (2012-2018): 25mm and 30mm
  • BMW F31 328i xDrive / 328d xDrive / 330i xDrive Sports Wagon (2014-2019): 25mm and 30mm
  • BMW F34 328i / 330i / 335i / 340i xDrive Gran Turismo (2014-2019): 25mm and 30mm
  • BMW F32 428i / 430i / 435i / 440i Coupe, incl. xDrive (2014-2020): 25mm and 30mm
  • BMW F33 428i / 430i / 435i / 440i Convertible, incl. xDrive (2014-2020): 25mm and 30mm
  • BMW F36 428i / 430i / 435i / 440i Gran Coupe, incl. xDrive (2015-2020): 25mm and 30mm
  • BMW F80 M3 Sedan (2015-2018): 25mm and 30mm
  • BMW F82 M4 Coupe (2015-2020), F83 M4 Convertible (2015-2020): 25mm and 30mm
  • BMW F10 M5 (2013-2016): 25mm and 30mm
  • BMW F06 M6 Gran Coupe (2014-2019): 25mm and 30mm
  • BMW F12 M6 Convertible / F13 M6 Coupe (2013-2018): 25mm and 30mm
  • BMW F10 528i / 535i / 535d / 550i (2011-2016): 25mm and 30mm
  • BMW F12 / F13 640i / 650i Convertible and Coupe, incl. xDrive (2012-2019): 25mm and 30mm
  • BMW F01 / F02 740i / 740Li / 750i / 750Li / 760Li, incl. xDrive and ActiveHybrid (2009-2015): 25mm and 30mm
  • BMW F07 535i / 550i Gran Turismo, incl. xDrive (2010-2016): 25mm and 30mm
  • BMW F25 X3 (2011-2017): 25mm and 30mm
  • BMW F26 X4 xDrive28i / xDrive35i / M40i (2015-2018): 25mm and 30mm

H&R lists these widths for each model. Not sure about your car? Send us your VIN and we will confirm before you order.

Installation Notes

A DRA install has two steps at each corner: the spacer bolts to the hub, then the wheel bolts to the spacer. Use a torque wrench for both. Professional installation is recommended.

  1. Clean the hub face and remove any rust or scale so the spacer sits flat.
  2. Bolt the DRA spacer to the hub with the special bolts supplied, tightened to the torque in the H&R instructions.
  3. Check that your factory wheel bolts are not long enough to reach the hub face once threaded into the spacer.
  4. Mount the wheel on the spacer and tighten the factory wheel bolts to factory torque in a star pattern.
  5. Turn the wheel by hand and check that nothing rubs. The wheel should spin freely.
  6. Re-check the torque on the spacer bolts and wheel bolts after the first short drive.