{"product_id":"dinan-valved-axle-back-exhaust-black-tips-bmw-g80-m3-g82-m4","title":"Dinan Valved Axle-Back Exhaust with Black Tips - BMW G80 M3 \/ G82 \/ G83 M4 (2021-2026)","description":"\u003cp\u003eThe S58 has plenty to say. The factory exhaust on your M3 or M4 lets some of it out, then tidies it up for the neighbors. You get a good noise in Sport Plus and a lot of muffler everywhere else. If you want the car to sound as serious as it drives, the rear section is where it starts.\u003c\/p\u003e\n\u003cp\u003eThe Dinan Valved Axle-Back Exhaust for the BMW G80 M3 and G82\/G83 M4 replaces the factory rear section with 76mm T304 stainless tubing and four 4.5 in. black ceramic tips. Dinan measured +6 HP and +5 lb-ft at 6600 RPM, and the system weighs 38 lbs against 44 lbs stock.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eHow the Dinan M3 Axle-Back Exhaust Handles Drone\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eSedan, coupe and convertible bodies resonate differently inside the cabin. A system that sounds right in an M4 can drone in an M3. Dinan developed one axle-back that behaves on all three body styles, then kept the factory exhaust valves working exactly as BMW designed them. Valves closed, exhaust routes through the Dinan muffler and exits the inner tips, so cold starts and highway miles stay civil. Valves open under high load, exhaust bypasses the muffler and you get near straight-pipe flow with the full S58 voice.\u003c\/p\u003e\n\u003cp\u003eThe tubing steps up from 70mm to 76mm and every piece is T304 stainless steel, TIG welded. The four 114mm double-walled clamp-on tips carry a black ceramic coating that suits a dark-trim M car.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eValved Axle-Back Exhaust Install and Legal Status\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eIt is a bolt-on axle-back with a Dinan-quoted labor time of 2.7 hours, and no coding is needed because the factory valve control stays in place. Dinan states it does not affect vehicle emissions and is legal for sale or use on emissions-controlled vehicles. Want more? Add the Dinan High Flow Middle Exhaust, which Dinan confirms fits with this axle-back. Dinan part number D660-0093-BLK. Sold by AutoTecknic, an authorized Dinan dealer.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhat's Included\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eDinan valved axle-back exhaust\u003c\/li\u003e\n  \u003cli\u003eFour 4.5 in. (114mm) double-walled black ceramic clamp-on tips\u003c\/li\u003e\n  \u003cli\u003eMounting hardware and clamps\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eKey Features\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eDinan-tested +6 HP and +5 lb-ft at 6600 RPM\u003c\/li\u003e\n  \u003cli\u003e76mm tubing vs 70mm stock\u003c\/li\u003e\n  \u003cli\u003eFactory exhaust valves retained with original operation\u003c\/li\u003e\n  \u003cli\u003eDeveloped for low drone on M3 sedan, M4 coupe and M4 convertible\u003c\/li\u003e\n  \u003cli\u003e6 lbs lighter than stock: 38 lbs vs 44 lbs\u003c\/li\u003e\n  \u003cli\u003e100% T304 stainless steel, TIG welded\u003c\/li\u003e\n  \u003cli\u003eFour 114mm double-walled tips with black ceramic coating\u003c\/li\u003e\n  \u003cli\u003eBolt-on install, about 2.7 hours\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eVehicle Fitment\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eFits the following S58-powered BMW M models:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eBMW M3 \/ G80 Sedan (2021-2026): M3, M3 Competition, M3 Competition xDrive\u003c\/li\u003e\n  \u003cli\u003eBMW M4 \/ G82 Coupe (2021-2026): M4, M4 Competition, M4 Competition xDrive\u003c\/li\u003e\n  \u003cli\u003eBMW M4 \/ G83 Convertible (2022-2026): M4 Competition xDrive Convertible\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNot confirmed for the M3 CS or M4 CSL. Contact us before ordering for those cars.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eInstallation Notes\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA shop familiar with G8X cars will have this in about 2.7 hours. A DIYer with a lift and basic hand tools can do it too. Follow the Dinan instructions included with the kit.\u003c\/p\u003e\n\u003col\u003e\n  \u003cli\u003eLet the exhaust cool completely and raise the car safely on a lift.\u003c\/li\u003e\n  \u003cli\u003eDisconnect the factory exhaust valve actuators and loosen the clamps ahead of the rear section.\u003c\/li\u003e\n  \u003cli\u003eSupport the factory rear section, release it from the hangers and remove it.\u003c\/li\u003e\n  \u003cli\u003eHang the Dinan axle-back on the factory mounting points, connect it with the supplied clamps and transfer the valve actuators as directed.\u003c\/li\u003e\n  \u003cli\u003eFit and align the four tips, torque all clamps, reconnect the actuators and check for leaks and valve operation in each drive mode.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"Dinan","offers":[{"title":"Default Title","offer_id":51268701618422,"sku":"DNND660-0093-BLK","price":2113.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2674\/6278\/files\/d65b4084d7428dc615ff59085afe6db2L.jpg?v=1784135590","url":"https:\/\/autotecknic.com\/products\/dinan-valved-axle-back-exhaust-black-tips-bmw-g80-m3-g82-m4","provider":"AutoTecknic USA","version":"1.0","type":"link"}