{"product_id":"autotecknic-dry-carbon-front-air-duct-trim-bmw-g07-x7-lci","title":"AutoTecknic Dry Carbon Front Air Duct Trim - BMW G07 X7 LCI M Sport","description":"\u003cp\u003eThe LCI X7's front bumper is built around two big lower air ducts, one on each side of the grille. From the factory, the trim that frames the top of each duct is plain black plastic. The AutoTecknic Dry Carbon Front Air Duct Trim replaces both pieces with real carbon weave, tracing the duct from the edge of the grille out and down toward the corner of the bumper. It's the line your eye follows across the front of the car, and now it's carbon.\u003c\/p\u003e\n\u003cp\u003eThis isn't a wrap, a hydro-dipped plastic part or a printed carbon pattern. Each trim is 100% genuine pre-preg dry carbon fiber in a gloss twill weave, shaped to match the factory part. The left and right sides come as a matched pair, so the weave lines up on both sides of the car.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003ePre-Preg Dry Carbon Front Air Duct Trim, Shaped to the Factory Part\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003ePre-preg carbon starts with the resin already infused into the fabric at a controlled ratio. It's then cured under heat and pressure. That makes it lighter and stiffer than wet-layup carbon, and you don't get the resin pooling, pinholes or cloudy patches that cheap carbon parts show up close. Each trim runs about 16 inches across the bumper, so the weave quality is on full display.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eBuilt for the LCI Front Bumper Only\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThese trims copy the shape, profile and mounting tabs of the factory LCI pieces. There's no added aero and no change to the bumper's silhouette. The Pre-LCI X7 uses a completely different front bumper, so these fit 2023 and newer LCI models only.\u003c\/p\u003e\n\u003cp\u003ePair them with the AutoTecknic Dry Carbon Front Bumper Inserts Set, which sits at the outer corner just below the headlights, for a matched carbon look across both sides of the front bumper.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhat's Included\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e1 x Left front air duct trim, dry carbon\u003c\/li\u003e\n  \u003cli\u003e1 x Right front air duct trim, dry carbon\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eInstalled photos may show other aero parts, sold separately. This listing includes the two air duct trims only.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eKey Features\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e100% genuine pre-preg dry carbon fiber, not a wrap, overlay film or hydro-dip\u003c\/li\u003e\n  \u003cli\u003eGloss twill weave finish\u003c\/li\u003e\n  \u003cli\u003eSold as a matched left and right pair\u003c\/li\u003e\n  \u003cli\u003eFactory shape with molded mounting tabs that clip into the factory mounting points\u003c\/li\u003e\n  \u003cli\u003eDirect replacement for the factory trims, no cutting, drilling or bumper removal\u003c\/li\u003e\n  \u003cli\u003eApproximately 41.5 cm (16.33 in) long and 17 cm (6.69 in) tall\u003c\/li\u003e\n  \u003cli\u003ePairs with the AutoTecknic Dry Carbon Front Bumper Inserts Set for a full carbon front end\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eVehicle Fitment\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eFits the BMW G07 X7 LCI with the M Sport front bumper:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eBMW G07 X7 LCI (2023-2027): xDrive40i with M Sport package, M60i\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNot compatible with the Pre-LCI X7 (2019-2022), the non-M Sport front bumper or the Alpina XB7.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eInstallation Notes\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThese trims replace the factory front air duct trims and install from the front with a plastic pry tool. No bumper removal needed. If you've pulled exterior trim on a BMW before, you can do this in your driveway. If you haven't, have a body shop or installer do it. Factory clips break easily, especially in cold weather.\u003c\/p\u003e\n\u003col\u003e\n  \u003cli\u003eWash and dry the front bumper around both air ducts.\u003c\/li\u003e\n  \u003cli\u003eDo one side at a time so the untouched side shows you how the factory trim sits.\u003c\/li\u003e\n  \u003cli\u003eUse a plastic pry tool to release the factory trim, working slowly from one end.\u003c\/li\u003e\n  \u003cli\u003eTest-fit the carbon trim and check alignment and panel gaps before seating it.\u003c\/li\u003e\n  \u003cli\u003eLine up the mounting tabs and press evenly until every tab seats fully, then repeat on the other side.\u003c\/li\u003e\n  \u003cli\u003eProtect the finish like paint, with a pH-neutral wash and a sealant or ceramic coating.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"AutoTecknic USA","offers":[{"title":"Default Title","offer_id":52111851290870,"sku":"ATK-BM-0439","price":445.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2674\/6278\/files\/autotecknic-bmw-g07-x7-lci-dry-carbon-front-air-duct-trim-01.jpg?v=1793654742","url":"https:\/\/autotecknic.com\/products\/autotecknic-dry-carbon-front-air-duct-trim-bmw-g07-x7-lci","provider":"AutoTecknic USA","version":"1.0","type":"link"}