{"title":"Dinan Wheel Spacers","description":"\u003cp\u003eDinan wheel spacers for BMW, sold in pairs from 5mm to 20mm. Fitments cover G-chassis cars on the 5x112 pattern with a 66.5mm center bore, and E and F-chassis cars on 5x120 with a 72.6mm center bore.\u003c\/p\u003e\n\u003cp\u003eThicker spacers usually need longer wheel bolts. Check the fitment notes on each listing, or send us your VIN and we will confirm the right part. See all \u003ca href=\"\/collections\/wheel-spacers-accessories\"\u003ewheel spacers and accessories\u003c\/a\u003e.\u003c\/p\u003e","products":[{"product_id":"dinan-5mm-wheel-spacers-bmw-g-chassis-5x112","title":"Dinan 5mm Black Wheel Spacers (Pair) - BMW G-Chassis 5x112 \/ 66.5mm CB","description":"\u003cp\u003eLook at your BMW from the rear three-quarter and the wheels sit just a little too far inside the arches. It is a small gap, but once you see it, you cannot unsee it. Five millimeters per side is often all it takes to fill that space and give the car the planted, square stance it should have had from the factory.\u003c\/p\u003e\n\u003cp\u003eDinan 5mm Wheel Spacers are CNC-machined from 6061 aluminum and anodized black for BMW G-chassis cars with the 5x112 bolt pattern, 66.5mm center bore and M14x1.25 lug bolts. Each spacer moves the wheel out 5mm from the hub, widening the track for a more aggressive look and a slightly wider stance through corners.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhy Dinan 5mm Wheel Spacers\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eCheap spacers are where wheel fitment problems start. Dinan machines these from 6061 aluminum to a precise 5mm thickness with a 66.5mm center bore matched to the G-chassis hub, then anodizes them black so they disappear behind the spokes. The weight-saving design keeps unsprung mass down. They are sold as a pair, so order two sets to do all four corners.\u003c\/p\u003e\n\u003cp\u003eWill they rub? At 5mm, most owners use them to fine-tune fitment rather than push the limits, but clearance always depends on your wheel width, offset and tire size. Check your setup, and if you are unsure, ask us before you order.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWheel Spacer Lug Bolts and Fitment\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eExtended lug bolts are required and sold separately. Dinan specifies M14x1.25 cone seat lug bolts and suggests D220-0003 (33mm) for this spacer. Never reuse your stock lug bolts with a spacer. Fitment follows Dinan's G-chassis spacer guide, and exceptions do apply, so confirm your car before ordering. Dinan part number D210-2023. Sold by AutoTecknic, an authorized Dinan dealer.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhat's Included\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e2 Dinan 5mm wheel spacers, black anodized\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eKey Features\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e5mm thick, moves each wheel out 5mm from the hub\u003c\/li\u003e\n  \u003cli\u003e5x112 bolt pattern, 66.5mm center bore\u003c\/li\u003e\n  \u003cli\u003eCNC-machined 6061 aluminum\u003c\/li\u003e\n  \u003cli\u003eAnodized black finish\u003c\/li\u003e\n  \u003cli\u003eWeight-saving design\u003c\/li\u003e\n  \u003cli\u003eSold as a pair\u003c\/li\u003e\n  \u003cli\u003eRequires extended M14x1.25 cone seat lug bolts, sold separately\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eVehicle Fitment\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eFits BMW vehicles that use Dinan's G-chassis spacer fitment:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eBMW G-Chassis: 5x112 bolt pattern, 66.5mm center bore, M14x1.25 lug bolts\u003c\/li\u003e\n  \u003cli\u003eBMW F9x M5 \/ M8: uses the G-chassis spacer fitment\u003c\/li\u003e\n  \u003cli\u003eBMW F48 X1 \/ F39 X2: uses the G-chassis spacer fitment\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eExceptions do apply. Confirm your vehicle's bolt pattern, center bore and lug bolt thread before ordering.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eInstallation Notes\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA quick job with a jack, stands and a torque wrench. Always use the correct extended lug bolts, never the stock bolts.\u003c\/p\u003e\n\u003col\u003e\n  \u003cli\u003eLoosen the lug bolts, raise the car and support it safely on jack stands.\u003c\/li\u003e\n  \u003cli\u003eRemove the wheel and clean any rust or debris from the hub face.\u003c\/li\u003e\n  \u003cli\u003eFit the spacer flat against the hub, centered on the 66.5mm hub bore.\u003c\/li\u003e\n  \u003cli\u003eMount the wheel with the extended M14x1.25 cone seat lug bolts and snug them in a star pattern.\u003c\/li\u003e\n  \u003cli\u003eLower the car, torque the bolts to BMW specification and re-check torque after the first 50 to 100 miles.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"Dinan","offers":[{"title":"Default Title","offer_id":51268688969974,"sku":"DNND210-2023","price":52.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2674\/6278\/files\/ec52146c87ba16f429ac687410a31f91L.jpg?v=1784135445"},{"product_id":"dinan-10mm-wheel-spacers-5x112-66-5mm-bmw-g-chassis","title":"Dinan 10mm Wheel Spacers Pair 5x112 66.5mm - BMW G-Chassis \/ F9x M5 \/ M8 \/ F48 X1 \/ F39 X2","description":"\u003cp\u003eYour wheels look great until you see them from the rear three-quarter and notice the gap between the tire sidewall and the fender lip. Ten millimeters per side pulls the wheel out toward the fender without buying new wheels or changing tire sizes.\u003c\/p\u003e\n\u003cp\u003eDinan 10mm wheel spacers (part number D210-2027) are machined for the BMW 5x112 bolt pattern and 66.5mm center bore used across the G-chassis lineup. They push each wheel 10mm further from the hub, widening your track for a fuller stance and extra room around big brake calipers. You get a pair, enough for one axle.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhy Dinan 10mm Wheel Spacers Are Worth It\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA spacer that does not center properly on the hub shows up as vibration at highway speed. These are CNC-machined from billet 6061 aluminum and anodized black, with a 66.5mm bore cut to BMW's G-chassis hub diameter so the spacer seats on the hub itself instead of floating on the studs.\u003c\/p\u003e\n\u003cp\u003eThe bigger question with any spacer is bolts. Your factory wheel bolts are sized for wheel-to-hub contact only, so adding 10mm means you need bolts 10mm longer to keep full thread engagement. Dinan calls out its 40mm M14x1.25 cone seat lug bolts for this spacer, which takes the guesswork out of it. Order those alongside and you are ready to bolt up.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhat's Included\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e2 x Dinan 10mm wheel spacers, 5x112, 66.5mm center bore\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eLug bolts are not included. Dinan's matching bolt for this spacer is the M14x1.25 cone seat 40mm set (sold separately).\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eKey Features\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e10mm thickness moves each wheel 10mm outboard\u003c\/li\u003e\n  \u003cli\u003e5x112 bolt pattern with 66.5mm center bore for BMW G-chassis hubs\u003c\/li\u003e\n  \u003cli\u003eCNC-machined billet 6061 aluminum\u003c\/li\u003e\n  \u003cli\u003eWeight-saving design\u003c\/li\u003e\n  \u003cli\u003eBlack anodized finish\u003c\/li\u003e\n  \u003cli\u003eSold as a pair (one axle)\u003c\/li\u003e\n  \u003cli\u003eDesigned to pair with Dinan 40mm M14x1.25 cone seat lug bolts\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eVehicle Fitment\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eDinan's application guide specifies this 5x112, 66.5mm center bore spacer (used with M14x1.25 bolts) for:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eBMW G-Chassis (5x112 \/ M14x1.25)\u003c\/li\u003e\n  \u003cli\u003eBMW F9x M5 \/ M8 and F48 X1 \/ F39 X2 (exceptions that use the G-chassis fitment of 5x112 with M14x1.25 bolts)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNot for E-chassis BMWs (5x120 \/ M12x1.5) or other F-chassis BMWs (5x120 \/ M14x1.25). Contact us before ordering if your car is not covered above.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eInstallation Notes\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA straightforward bolt-on job with a jack, jack stands and a torque wrench. The critical step is using longer bolts: Dinan matches its 40mm M14x1.25 cone seat bolts to 10mm and 12mm spacers. Confirm your wheels use a cone seat before ordering bolts, and check tire-to-fender clearance at full steering lock, especially on staggered or aggressive-offset setups.\u003c\/p\u003e\n\u003col\u003e\n  \u003cli\u003eLoosen the wheel bolts, raise the car and support it on jack stands.\u003c\/li\u003e\n  \u003cli\u003eRemove the wheel and clean any rust or debris from the hub face.\u003c\/li\u003e\n  \u003cli\u003eSlide the spacer over the hub pilot so it sits flush against the hub face.\u003c\/li\u003e\n  \u003cli\u003eMount the wheel and thread in the 40mm lug bolts by hand.\u003c\/li\u003e\n  \u003cli\u003eSnug the bolts in a star pattern, lower the car and torque to your BMW's factory wheel bolt specification.\u003c\/li\u003e\n  \u003cli\u003eRecheck torque after the first short drive.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"Dinan","offers":[{"title":"Default Title","offer_id":51268689232118,"sku":"DNND210-2027","price":76.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2674\/6278\/files\/f4e02804a6774f4d3420cdffe53c3f73L.jpg?v=1784135449"},{"product_id":"dinan-15mm-wheel-spacers-5x112-66-5mm-bmw-g-chassis","title":"Dinan 15mm Wheel Spacers Pair 5x112 66.5mm - BMW G-Chassis","description":"\u003cp\u003eFifteen millimeters is the size where a G-chassis BMW stops looking like it rolled off the dealer lot. The tire moves from tucked inside the arch to sitting right under the fender lip, and the car looks planted from every angle.\u003c\/p\u003e\n\u003cp\u003eDinan 15mm wheel spacers (part number D210-2029) are machined for the BMW 5x112 bolt pattern and 66.5mm center bore used across the G-chassis lineup. Each spacer moves the wheel 15mm further from the hub, widening your track for a fuller stance and more room around big brake calipers. You get a pair, enough for one axle.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhy Dinan 15mm Wheel Spacers Are Worth It\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA spacer that does not center on the hub shows up as a shimmy at highway speed. These are CNC-machined from billet 6061 aluminum and anodized black, with a 66.5mm bore cut to BMW's G-chassis hub diameter. Dinan lists hub-centric rings on its larger spacer sizes, so the wheel is located by the hub and not by the bolts.\u003c\/p\u003e\n\u003cp\u003eThe real question with any spacer is bolts. Your factory wheel bolts are sized for wheel-to-hub contact only. Add 15mm and you need bolts long enough to keep full thread engagement. Dinan calls out its 45mm M14x1.25 cone seat lug bolts for this spacer, so there is no guessing. Order them together and you are ready to bolt up.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhat's Included\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e2 x Dinan 15mm wheel spacers, 5x112, 66.5mm center bore\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eLug bolts are not included. Dinan's matching bolt for this spacer is the M14x1.25 cone seat 45mm set of 10 (sold separately).\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eKey Features\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e15mm thickness moves each wheel 15mm outboard\u003c\/li\u003e\n  \u003cli\u003e5x112 bolt pattern with 66.5mm center bore for BMW G-chassis hubs\u003c\/li\u003e\n  \u003cli\u003eCNC-machined billet 6061 aluminum\u003c\/li\u003e\n  \u003cli\u003eWeight-saving design\u003c\/li\u003e\n  \u003cli\u003eBlack anodized finish\u003c\/li\u003e\n  \u003cli\u003eSold as a pair (one axle)\u003c\/li\u003e\n  \u003cli\u003eDesigned to pair with Dinan 45mm M14x1.25 cone seat lug bolts\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eVehicle Fitment\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eDinan specifies this spacer by chassis family, not by individual model:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eBMW G-Chassis: 5x112 bolt pattern, 66.5mm center bore, M14x1.25 lug bolts\u003c\/li\u003e\n  \u003cli\u003eDinan-listed exceptions that also use this G-chassis fitment: F90 M5, F91 \/ F92 \/ F93 M8, F48 X1, F39 X2\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNot for E-chassis or 5x120 F-chassis BMWs. If your car is not a G-chassis model or one of the exceptions above, contact us before ordering.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eInstallation Notes\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA bolt-on job with a jack, jack stands and a torque wrench. The one step you cannot skip is longer bolts: Dinan matches its 45mm M14x1.25 cone seat bolts to this spacer. At 15mm the wheel moves out a meaningful amount, so check tire-to-fender clearance at full steering lock and full compression, especially on staggered or aggressive-offset setups.\u003c\/p\u003e\n\u003col\u003e\n  \u003cli\u003eLoosen the wheel bolts, raise the car and support it on jack stands.\u003c\/li\u003e\n  \u003cli\u003eRemove the wheel and clean any rust or debris from the hub face.\u003c\/li\u003e\n  \u003cli\u003eSlide the spacer over the hub pilot so it sits flush against the hub face.\u003c\/li\u003e\n  \u003cli\u003eMount the wheel and thread in the 45mm lug bolts by hand.\u003c\/li\u003e\n  \u003cli\u003eSnug the bolts in a star pattern, lower the car and torque to your BMW's factory wheel bolt specification.\u003c\/li\u003e\n  \u003cli\u003eRecheck torque after the first short drive.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"Dinan","offers":[{"title":"Default Title","offer_id":51268689297654,"sku":"DNND210-2029","price":86.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2674\/6278\/files\/1736a40f48e9ab50c94fe357210d52d8L.jpg?v=1784135449"},{"product_id":"dinan-20mm-wheel-spacers-5x112-66-5mm-bmw-g-chassis","title":"Dinan 20mm Wheel Spacers Pair 5x112 66.5mm - BMW G-Chassis","description":"\u003cp\u003eTwenty millimeters is for the owner who wants the wheels right at the fender edge. It is the biggest visual change you can make to a G-chassis BMW with a bolt-on part, and one of the few that also buys real clearance for big brake kits.\u003c\/p\u003e\n\u003cp\u003eDinan 20mm wheel spacers (part number D210-2031) are machined for the BMW 5x112 bolt pattern and 66.5mm center bore used across the G-chassis lineup. Each spacer moves the wheel 20mm further from the hub, widening your track for a fuller stance and more room around big brake calipers. You get a pair, enough for one axle.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhy Dinan 20mm Wheel Spacers Are Worth It\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA spacer that does not center on the hub shows up as a shimmy at highway speed. These are CNC-machined from billet 6061 aluminum and anodized black, with a 66.5mm bore cut to BMW's G-chassis hub diameter. Dinan lists hub-centric rings on its larger spacer sizes, so the wheel is located by the hub and not by the bolts.\u003c\/p\u003e\n\u003cp\u003eThe real question with any spacer is bolts. Your factory wheel bolts are sized for wheel-to-hub contact only. Add 20mm and you need bolts long enough to keep full thread engagement. Dinan calls out its 50mm M14x1.25 cone seat lug bolts for this spacer, so there is no guessing. Order them together and you are ready to bolt up.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhat's Included\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e2 x Dinan 20mm wheel spacers, 5x112, 66.5mm center bore\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eLug bolts are not included. Dinan's matching bolt for this spacer is the M14x1.25 cone seat 50mm set of 10 (sold separately).\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eKey Features\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e20mm thickness moves each wheel 20mm outboard\u003c\/li\u003e\n  \u003cli\u003e5x112 bolt pattern with 66.5mm center bore for BMW G-chassis hubs\u003c\/li\u003e\n  \u003cli\u003eCNC-machined billet 6061 aluminum\u003c\/li\u003e\n  \u003cli\u003eWeight-saving design\u003c\/li\u003e\n  \u003cli\u003eBlack anodized finish\u003c\/li\u003e\n  \u003cli\u003eSold as a pair (one axle)\u003c\/li\u003e\n  \u003cli\u003eDesigned to pair with Dinan 50mm M14x1.25 cone seat lug bolts\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eVehicle Fitment\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eDinan specifies this spacer by chassis family, not by individual model:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eBMW G-Chassis: 5x112 bolt pattern, 66.5mm center bore, M14x1.25 lug bolts\u003c\/li\u003e\n  \u003cli\u003eDinan-listed exceptions that also use this G-chassis fitment: F90 M5, F91 \/ F92 \/ F93 M8, F48 X1, F39 X2\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNot for E-chassis or 5x120 F-chassis BMWs. If your car is not a G-chassis model or one of the exceptions above, contact us before ordering.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eInstallation Notes\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA bolt-on job with a jack, jack stands and a torque wrench. The one step you cannot skip is longer bolts: Dinan matches its 50mm M14x1.25 cone seat bolts to this spacer. At 20mm the wheel moves out a meaningful amount, so check tire-to-fender clearance at full steering lock and full compression, especially on staggered or aggressive-offset setups.\u003c\/p\u003e\n\u003col\u003e\n  \u003cli\u003eLoosen the wheel bolts, raise the car and support it on jack stands.\u003c\/li\u003e\n  \u003cli\u003eRemove the wheel and clean any rust or debris from the hub face.\u003c\/li\u003e\n  \u003cli\u003eSlide the spacer over the hub pilot so it sits flush against the hub face.\u003c\/li\u003e\n  \u003cli\u003eMount the wheel and thread in the 50mm lug bolts by hand.\u003c\/li\u003e\n  \u003cli\u003eSnug the bolts in a star pattern, lower the car and torque to your BMW's factory wheel bolt specification.\u003c\/li\u003e\n  \u003cli\u003eRecheck torque after the first short drive.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"Dinan","offers":[{"title":"Default Title","offer_id":51268689461494,"sku":"DNND210-2031","price":93.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2674\/6278\/files\/18577a5871cb89230eaf07e50d929aeaL.jpg?v=1784135451"},{"product_id":"dinan-10mm-wheel-spacers-5x120-72-6mm-bmw-e-f-chassis","title":"Dinan 10mm Wheel Spacers Pair 5x120 72.6mm - BMW E \/ F-Chassis","description":"\u003cp\u003eE46, E90, F30, F80. Different decades, same problem: wheels that sit a little too far inside the arches from the factory. Ten millimeters per side is the subtle fix. It pulls the wheel out toward the fender line without changing wheels, tires or ride height.\u003c\/p\u003e\n\u003cp\u003eDinan 10mm wheel spacers (part number D210-2039) are machined for the BMW 5x120 bolt pattern and 72.6mm center bore used on E-chassis and F-chassis cars. Each spacer moves the wheel 10mm further from the hub for a fuller stance and extra clearance around brake calipers. You get a pair, enough for one axle.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhy Dinan 10mm Wheel Spacers for 5x120 BMWs\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThese are CNC-machined from billet 6061 aluminum and anodized black, with a 72.6mm bore cut to the BMW 5x120 hub diameter so the spacer seats on the hub itself instead of floating on the bolts.\u003c\/p\u003e\n\u003cp\u003eBolts are where people get caught out. Every spacer, even a 10mm, needs longer lug bolts, and the thread depends on your chassis. E-chassis cars use M12x1.5 bolts. F-chassis cars use M14x1.25. Dinan's matches for this spacer are its 39mm M12x1.5 cone seat bolts for E-chassis and its 40mm M14x1.25 cone seat bolts for F-chassis, both sold separately. Get the right set and the install is simple.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhat's Included\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e2 x Dinan 10mm wheel spacers, 5x120, 72.6mm center bore\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eLug bolts are not included. Order the Dinan 39mm M12x1.5 (E-chassis) or 40mm M14x1.25 (F-chassis) cone seat bolt set separately.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eKey Features\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e10mm thickness moves each wheel 10mm outboard\u003c\/li\u003e\n  \u003cli\u003e5x120 bolt pattern with 72.6mm center bore\u003c\/li\u003e\n  \u003cli\u003eCNC-machined billet 6061 aluminum\u003c\/li\u003e\n  \u003cli\u003eWeight-saving design\u003c\/li\u003e\n  \u003cli\u003eBlack anodized finish\u003c\/li\u003e\n  \u003cli\u003eSold as a pair (one axle)\u003c\/li\u003e\n  \u003cli\u003eWorks with Dinan 39mm M12x1.5 or 40mm M14x1.25 cone seat lug bolts, depending on chassis\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eVehicle Fitment\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eDinan specifies this spacer by chassis family, not by individual model:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eBMW E-Chassis: 5x120 bolt pattern, M12x1.5 lug bolts\u003c\/li\u003e\n  \u003cli\u003eBMW F-Chassis: 5x120 bolt pattern, M14x1.25 lug bolts\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eDinan-listed exceptions: the F90 M5, F91 \/ F92 \/ F93 M8, F48 X1 and F39 X2 use G-chassis 5x112 fitment and do not take this spacer. This spacer has a 72.6mm center bore. Some large BMWs use a bigger 74.1mm hub bore, including the E39 5 Series, E38 7 Series and the X5 \/ X6 (E53, E70, E71, F15, F16). Confirm your hub bore before ordering, or contact us and we will check it for you.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eInstallation Notes\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA bolt-on job with a jack, jack stands and a torque wrench. Match the bolt thread to your chassis (M12x1.5 for E-chassis, M14x1.25 for F-chassis) and confirm your wheels use a cone seat before ordering bolts.\u003c\/p\u003e\n\u003col\u003e\n  \u003cli\u003eLoosen the wheel bolts, raise the car and support it on jack stands.\u003c\/li\u003e\n  \u003cli\u003eRemove the wheel and clean any rust or debris from the hub face.\u003c\/li\u003e\n  \u003cli\u003eSlide the spacer over the hub pilot so it sits flush against the hub face.\u003c\/li\u003e\n  \u003cli\u003eMount the wheel and thread in the longer lug bolts by hand.\u003c\/li\u003e\n  \u003cli\u003eSnug the bolts in a star pattern, lower the car and torque to your BMW's factory wheel bolt specification.\u003c\/li\u003e\n  \u003cli\u003eRecheck torque after the first short drive.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"Dinan","offers":[{"title":"Default Title","offer_id":51268689953014,"sku":"DNND210-2039","price":74.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2674\/6278\/files\/aaed565a529e7a7a1d4bb869cd3c6103L.jpg?v=1784135457"},{"product_id":"dinan-wheel-spacers-5x112-12mm-bmw-g-chassis","title":"Dinan 12mm Wheel Spacers 5x112 (Set of 2) - BMW G Chassis \/ F9X M5 \/ M8 \/ F48 X1 \/ F39 X2","description":"\u003cp\u003eLook at almost any BMW from the side and the wheels sit a little too far inside the arches. The factory does it on purpose to cover every tire and chain combination. You do not need that margin, and 12mm per side is often exactly what it takes to make the car look planted instead of tucked in.\u003c\/p\u003e\n\u003cp\u003eDinan 12mm Wheel Spacers move each wheel outward to fill the fender properly or to gain clearance for a larger brake caliper. They are made for the BMW G chassis 5x112 bolt pattern with a 66.5mm center bore, CNC-machined from 6061 billet aluminum and anodized black. Sold as a set of 2, one axle per set.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eDinan 12mm Wheel Spacers: Precision Where It Counts\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA spacer sits in the most safety-critical joint on the car, so how it is made matters more than how it looks. Dinan machines these from billet 6061 aluminum rather than casting them, with a weight saving design and a 66.5mm center bore sized to the BMW G chassis hub. The black anodized finish stands up to road salt and brake dust and disappears behind the spokes.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eLug Bolts, Fitment and What to Check Before You Order\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eYour factory lug bolts will be too short once a 12mm spacer is in place. You need longer M14x1.25 cone seat lug bolts, sold separately. Dinan offers them as D220-0005 (40mm), D220-0006 (45mm) and D220-0007 (50mm). The right length depends on your wheel, so ask us if you are unsure. Also confirm your car is a 5x112 BMW: E chassis and most F chassis cars use 5x120 and need a different spacer. Dinan part number D210-2028. Sold by AutoTecknic, an authorized Dinan dealer.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhat's Included\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eTwo 12mm wheel spacers, 5x112, 66.5mm center bore\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eKey Features\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e12mm thick, 5x112 bolt pattern, 66.5mm center bore\u003c\/li\u003e\n  \u003cli\u003eCNC-machined 6061 billet aluminum\u003c\/li\u003e\n  \u003cli\u003eWeight saving design\u003c\/li\u003e\n  \u003cli\u003eAnodized black finish\u003c\/li\u003e\n  \u003cli\u003eSet of 2, enough for one axle\u003c\/li\u003e\n  \u003cli\u003eUses M14x1.25 cone seat lug bolts (sold separately)\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eVehicle Fitment\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eFits BMW models that use Dinan's G chassis spacer fitment (5x112 bolt pattern, M14x1.25 lug bolts):\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eBMW G chassis models (5x112, M14x1.25 lug bolts)\u003c\/li\u003e\n  \u003cli\u003eBMW F90 M5 and F91 \/ F92 \/ F93 M8 (use the G chassis spacer fitment)\u003c\/li\u003e\n  \u003cli\u003eBMW F48 X1 and F39 X2 (use the G chassis spacer fitment)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNot for: E chassis BMWs (5x120, M12x1.5 lug bolts) or F chassis BMWs outside the exceptions above (5x120). Dinan does not offer a spacer and bolt combination for the E39 5 Series or E\/F chassis X5 and X6.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eInstallation Notes\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eIf you can swap a wheel, you can fit these. The one step you cannot skip is the longer lug bolts. Never reuse factory bolts with a spacer.\u003c\/p\u003e\n\u003col\u003e\n  \u003cli\u003eLoosen the lug bolts, raise the car on a lift or jack stands and remove the wheel.\u003c\/li\u003e\n  \u003cli\u003eClean any rust or debris from the hub face so the spacer sits flat.\u003c\/li\u003e\n  \u003cli\u003eSlide the spacer over the hub and seat it flush.\u003c\/li\u003e\n  \u003cli\u003eRefit the wheel with the correct length M14x1.25 cone seat lug bolts and torque them to BMW specification.\u003c\/li\u003e\n  \u003cli\u003eRe-check lug bolt torque after the first drive.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"Dinan","offers":[{"title":"Default Title","offer_id":51283292455158,"sku":"DNND210-2028","price":74.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2674\/6278\/files\/d4550e2f240e7c542e1fdb7fdea0a673L.jpg?v=1784309564"},{"product_id":"dinan-6mm-wheel-spacers-bmw-g-chassis-5x112","title":"Dinan 6mm Wheel Spacers 5x112 66.5mm CB (Set of 2) - BMW G Chassis","description":"\u003cp\u003eYour wheels sit a little too far inside the fenders, or a new brake setup needs a touch more caliper clearance. You do not need new wheels to fix it. Six millimeters goes a long way.\u003c\/p\u003e\n\u003cp\u003eDinan 6mm Wheel Spacers physically move the wheel further out from the hub, giving your wheels the offset needed for the stance you want or the clearance your brake calipers need. Each spacer is machined from billet 6061 aluminum, anodized black, with a 5x112 bolt pattern and a 66.5mm center bore. They are sold as a set of 2, enough for one axle.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhich BMW Chassis These Dinan Wheel Spacers Fit\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eDinan sizes its spacers by chassis family. This 5x112 spacer is for BMW G chassis models, which use M14x1.25 lug bolts. Dinan also notes exceptions that use the G chassis spacer fitment, including the F9x M5 and M8 and the F48 X1 and F39 X2. E and F chassis cars that use a 5x120 bolt pattern need a different Dinan spacer.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eLug Bolts, Clearance and Safe Install\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eSpacers always need longer lug bolts, and they are sold separately. For G chassis cars, Dinan offers M14x1.25 extended bolts in 35mm and 40mm lengths, and the right length depends on your spacer and wheel. Before you drive, check wheel to caliper and wheel to fender clearance with the spacer fitted. Dinan part number D210-2024. Sold by AutoTecknic, an authorized Dinan dealer.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhat's Included\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eTwo Dinan 6mm wheel spacers\u003c\/li\u003e\n  \u003cli\u003eExtended lug bolts are sold separately\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eKey Features\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e6mm thickness per spacer\u003c\/li\u003e\n  \u003cli\u003e5x112 bolt pattern, 66.5mm center bore\u003c\/li\u003e\n  \u003cli\u003eBillet 6061 aluminum\u003c\/li\u003e\n  \u003cli\u003eAnodized black finish\u003c\/li\u003e\n  \u003cli\u003eSold as a pair for one axle\u003c\/li\u003e\n  \u003cli\u003eAdjusts offset for stance or brake caliper clearance\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eVehicle Fitment\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eFits by chassis family, per Dinan's application guide:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eBMW G chassis models (5x112 bolt pattern, M14x1.25 lug bolts)\u003c\/li\u003e\n  \u003cli\u003eExceptions that use G chassis spacer fitment: F9x M5 and M8, F48 X1 and F39 X2\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNot for E or F chassis models with the 5x120 bolt pattern, other than the exceptions above. Exceptions may not be limited to this list, so contact us with your VIN if you are unsure.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eInstallation Notes\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA basic job for anyone who has changed a wheel, as long as you use the correct extended bolts and a torque wrench.\u003c\/p\u003e\n\u003col\u003e\n  \u003cli\u003eLoosen the lug bolts, raise the car safely and remove the wheel.\u003c\/li\u003e\n  \u003cli\u003eClean the hub face so the spacer sits completely flat.\u003c\/li\u003e\n  \u003cli\u003eFit the spacer over the hub and mount the wheel with the correct length extended lug bolts.\u003c\/li\u003e\n  \u003cli\u003eTorque the lug bolts to BMW specification in a star pattern.\u003c\/li\u003e\n  \u003cli\u003eCheck clearance and recheck lug bolt torque after the first drive.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"Dinan","offers":[{"title":"Default Title","offer_id":51564134793462,"sku":"DNND210-2024","price":52.95,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2674\/6278\/files\/5ccf29f905bc1b24044e120379926206L.jpg?v=1788047400"},{"product_id":"dinan-7mm-wheel-spacers-5x112-66-5mm-bmw-g-chassis","title":"Dinan 7mm Wheel Spacers Pair 5x112 66.5mm - BMW G-Chassis","description":"\u003cp\u003ePark your BMW next to one that is sorted and you see it straight away: the wheels on yours sit a few millimeters too deep in the arches. Seven millimeters per side is a small number that makes a visible difference, pulling the tire out toward the fender lip without pushing it into rubbing territory on most setups.\u003c\/p\u003e\n\u003cp\u003eDinan 7mm wheel spacers (part number D210-2025) are machined for the BMW 5x112 bolt pattern and 66.5mm center bore used across the G-chassis lineup. Each spacer moves the wheel 7mm further from the hub, widening your track for a fuller stance and more room around big brake calipers. You get a pair, enough for one axle.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhy Dinan 7mm Wheel Spacers Are Worth It\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eCheap spacers are where wheel fitment problems start. These are CNC-machined from billet 6061 aluminum and anodized black so they disappear behind the spokes. The 66.5mm bore is cut to BMW's G-chassis hub diameter so the spacer sits square on the hub face. The weight-saving design keeps unsprung mass down.\u003c\/p\u003e\n\u003cp\u003eWill they rub? At 7mm most owners use them to fine-tune a stance rather than chase an extreme fitment, but clearance always depends on your wheel width, offset and tire size. Check your setup, and if you are unsure, ask us before you order. The other question is bolts. Your factory wheel bolts are sized for wheel-to-hub contact only. Dinan calls out its 35mm M14x1.25 cone seat lug bolts for 6mm, 7mm and 8mm spacers, so there is no guessing. Sold by AutoTecknic, an authorized Dinan dealer.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhat's Included\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e2 x Dinan 7mm wheel spacers, 5x112, 66.5mm center bore\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eLug bolts are not included. Dinan's matching bolt for this spacer is the M14x1.25 cone seat 35mm set of 10 (sold separately).\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eKey Features\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e7mm thickness moves each wheel 7mm outboard\u003c\/li\u003e\n  \u003cli\u003e5x112 bolt pattern with 66.5mm center bore for BMW G-chassis hubs\u003c\/li\u003e\n  \u003cli\u003eCNC-machined billet 6061 aluminum\u003c\/li\u003e\n  \u003cli\u003eWeight-saving design\u003c\/li\u003e\n  \u003cli\u003eBlack anodized finish\u003c\/li\u003e\n  \u003cli\u003eSold as a pair (one axle)\u003c\/li\u003e\n  \u003cli\u003eDesigned to pair with Dinan 35mm M14x1.25 cone seat lug bolts\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eVehicle Fitment\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eDinan specifies this spacer by chassis family, not by individual model:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eBMW G-Chassis: 5x112 bolt pattern, 66.5mm center bore, M14x1.25 lug bolts\u003c\/li\u003e\n  \u003cli\u003eDinan-listed exceptions that also use this G-chassis fitment: F90 M5, F91 \/ F92 \/ F93 M8, F48 X1, F39 X2\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNot for E-chassis or 5x120 F-chassis BMWs. If your car is not a G-chassis model or one of the exceptions above, contact us before ordering.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eInstallation Notes\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA bolt-on job with a jack, jack stands and a torque wrench. The one step you cannot skip is longer bolts: Dinan matches its 35mm M14x1.25 cone seat bolts to this spacer. Never reuse your factory bolts with a spacer. Check tire-to-fender clearance at full steering lock before driving.\u003c\/p\u003e\n\u003col\u003e\n  \u003cli\u003eLoosen the wheel bolts, raise the car and support it on jack stands.\u003c\/li\u003e\n  \u003cli\u003eRemove the wheel and clean any rust or debris from the hub face.\u003c\/li\u003e\n  \u003cli\u003eSlide the spacer over the hub pilot so it sits flush against the hub face.\u003c\/li\u003e\n  \u003cli\u003eMount the wheel and thread in the 35mm lug bolts by hand.\u003c\/li\u003e\n  \u003cli\u003eSnug the bolts in a star pattern, lower the car and torque to your BMW's factory wheel bolt specification.\u003c\/li\u003e\n  \u003cli\u003eRecheck torque after the first short drive.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"Dinan","offers":[{"title":"Default Title","offer_id":51564134891766,"sku":"DNND210-2025","price":74.95,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2674\/6278\/files\/22440825a98f9e41c2464bb93190a7d5L.jpg?v=1788047402"},{"product_id":"dinan-8mm-wheel-spacers-5x112-66-5mm-bmw-g-chassis","title":"Dinan 8mm Wheel Spacers Pair 5x112 66.5mm - BMW G-Chassis","description":"\u003cp\u003eEight millimeters is the thickest of the fine-tune spacer sizes. It is enough to pull a tucked wheel out to where the tire lines up with the fender, and on a lowered G-chassis BMW it is often the difference between a car that looks stock and one that looks finished.\u003c\/p\u003e\n\u003cp\u003eDinan 8mm wheel spacers (part number D210-2026) are machined for the BMW 5x112 bolt pattern and 66.5mm center bore used across the G-chassis lineup. Each spacer moves the wheel 8mm further from the hub, widening your track for a fuller stance and more room around big brake calipers. You get a pair, enough for one axle.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhy Dinan 8mm Wheel Spacers Are Worth It\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eCheap spacers are where wheel fitment problems start. These are CNC-machined from billet 6061 aluminum and anodized black so they disappear behind the spokes. The 66.5mm bore is cut to BMW's G-chassis hub diameter so the spacer sits square on the hub face. The weight-saving design keeps unsprung mass down.\u003c\/p\u003e\n\u003cp\u003eThe real question with any spacer is bolts. Your factory wheel bolts are sized for wheel-to-hub contact only, and at 8mm they will no longer reach full thread engagement. Dinan calls out its 35mm M14x1.25 cone seat lug bolts for 6mm, 7mm and 8mm spacers, so there is no guessing. Order them together and you are ready to bolt up. Clearance always depends on your wheel width, offset and tire size, so check your setup or ask us before you order. Sold by AutoTecknic, an authorized Dinan dealer.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhat's Included\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e2 x Dinan 8mm wheel spacers, 5x112, 66.5mm center bore\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eLug bolts are not included. Dinan's matching bolt for this spacer is the M14x1.25 cone seat 35mm set of 10 (sold separately).\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eKey Features\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e8mm thickness moves each wheel 8mm outboard\u003c\/li\u003e\n  \u003cli\u003e5x112 bolt pattern with 66.5mm center bore for BMW G-chassis hubs\u003c\/li\u003e\n  \u003cli\u003eCNC-machined billet 6061 aluminum\u003c\/li\u003e\n  \u003cli\u003eWeight-saving design\u003c\/li\u003e\n  \u003cli\u003eBlack anodized finish\u003c\/li\u003e\n  \u003cli\u003eSold as a pair (one axle)\u003c\/li\u003e\n  \u003cli\u003eDesigned to pair with Dinan 35mm M14x1.25 cone seat lug bolts\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eVehicle Fitment\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eDinan specifies this spacer by chassis family, not by individual model:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eBMW G-Chassis: 5x112 bolt pattern, 66.5mm center bore, M14x1.25 lug bolts\u003c\/li\u003e\n  \u003cli\u003eDinan-listed exceptions that also use this G-chassis fitment: F90 M5, F91 \/ F92 \/ F93 M8, F48 X1, F39 X2\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNot for E-chassis or 5x120 F-chassis BMWs. If your car is not a G-chassis model or one of the exceptions above, contact us before ordering.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eInstallation Notes\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA bolt-on job with a jack, jack stands and a torque wrench. The one step you cannot skip is longer bolts: Dinan matches its 35mm M14x1.25 cone seat bolts to this spacer. Never reuse your factory bolts with a spacer. Check tire-to-fender clearance at full steering lock before driving.\u003c\/p\u003e\n\u003col\u003e\n  \u003cli\u003eLoosen the wheel bolts, raise the car and support it on jack stands.\u003c\/li\u003e\n  \u003cli\u003eRemove the wheel and clean any rust or debris from the hub face.\u003c\/li\u003e\n  \u003cli\u003eSlide the spacer over the hub pilot so it sits flush against the hub face.\u003c\/li\u003e\n  \u003cli\u003eMount the wheel and thread in the 35mm lug bolts by hand.\u003c\/li\u003e\n  \u003cli\u003eSnug the bolts in a star pattern, lower the car and torque to your BMW's factory wheel bolt specification.\u003c\/li\u003e\n  \u003cli\u003eRecheck torque after the first short drive.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"Dinan","offers":[{"title":"Default Title","offer_id":51564134957302,"sku":"DNND210-2026","price":76.95,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2674\/6278\/files\/87871bac404b3e840cc9179dfe3795f9L.jpg?v=1788047403"},{"product_id":"dinan-17mm-wheel-spacers-5x112-66-5mm-bmw-g-chassis","title":"Dinan 17mm Wheel Spacers Pair 5x112 66.5mm - BMW G-Chassis","description":"\u003cp\u003eSeventeen millimeters is where a spacer stops being a fine-tune and starts changing how the car sits. Wheels with conservative offsets that looked lost inside the arches move right out to the fender line, and the car gains a wider, more planted stance from every angle.\u003c\/p\u003e\n\u003cp\u003eDinan 17mm wheel spacers (part number D210-2030) are machined for the BMW 5x112 bolt pattern and 66.5mm center bore used across the G-chassis lineup. Each spacer moves the wheel 17mm further from the hub, widening your track for a fuller stance and more room around big brake calipers. You get a pair, enough for one axle.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhy Dinan 17mm Wheel Spacers Are Worth It\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eCheap spacers are where wheel fitment problems start. These are CNC-machined from billet 6061 aluminum and anodized black so they disappear behind the spokes. Dinan lists hub-centric rings on its larger spacer sizes, so the wheel is located by the hub and not by the bolts. The weight-saving design keeps unsprung mass down.\u003c\/p\u003e\n\u003cp\u003eThe real question with any spacer is bolts, and at 17mm it matters more than ever. Your factory wheel bolts are sized for wheel-to-hub contact only. Dinan calls out its 45mm M14x1.25 cone seat lug bolts for 15mm and 17mm spacers, so there is no guessing. Order them together and you are ready to bolt up. Sold by AutoTecknic, an authorized Dinan dealer.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhat's Included\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e2 x Dinan 17mm wheel spacers, 5x112, 66.5mm center bore\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eLug bolts are not included. Dinan's matching bolt for this spacer is the M14x1.25 cone seat 45mm set of 10 (sold separately).\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eKey Features\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e17mm thickness moves each wheel 17mm outboard\u003c\/li\u003e\n  \u003cli\u003e5x112 bolt pattern with 66.5mm center bore for BMW G-chassis hubs\u003c\/li\u003e\n  \u003cli\u003eCNC-machined billet 6061 aluminum\u003c\/li\u003e\n  \u003cli\u003eWeight-saving design\u003c\/li\u003e\n  \u003cli\u003eBlack anodized finish\u003c\/li\u003e\n  \u003cli\u003eSold as a pair (one axle)\u003c\/li\u003e\n  \u003cli\u003eDesigned to pair with Dinan 45mm M14x1.25 cone seat lug bolts\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eVehicle Fitment\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eDinan specifies this spacer by chassis family, not by individual model:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eBMW G-Chassis: 5x112 bolt pattern, 66.5mm center bore, M14x1.25 lug bolts\u003c\/li\u003e\n  \u003cli\u003eDinan-listed exceptions that also use this G-chassis fitment: F90 M5, F91 \/ F92 \/ F93 M8, F48 X1, F39 X2\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNot for E-chassis or 5x120 F-chassis BMWs. If your car is not a G-chassis model or one of the exceptions above, contact us before ordering.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eInstallation Notes\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA bolt-on job with a jack, jack stands and a torque wrench. The one step you cannot skip is longer bolts: Dinan matches its 45mm M14x1.25 cone seat bolts to this spacer. Never reuse your factory bolts with a spacer. At 17mm the wheel moves out a meaningful amount, so check tire-to-fender clearance at full steering lock and full compression, especially on staggered or aggressive-offset setups.\u003c\/p\u003e\n\u003col\u003e\n  \u003cli\u003eLoosen the wheel bolts, raise the car and support it on jack stands.\u003c\/li\u003e\n  \u003cli\u003eRemove the wheel and clean any rust or debris from the hub face.\u003c\/li\u003e\n  \u003cli\u003eSlide the spacer over the hub pilot so it sits flush against the hub face.\u003c\/li\u003e\n  \u003cli\u003eMount the wheel and thread in the 45mm lug bolts by hand.\u003c\/li\u003e\n  \u003cli\u003eSnug the bolts in a star pattern, lower the car and torque to your BMW's factory wheel bolt specification.\u003c\/li\u003e\n  \u003cli\u003eRecheck torque after the first short drive.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"Dinan","offers":[{"title":"Default Title","offer_id":51564134990070,"sku":"DNND210-2030","price":93.95,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2674\/6278\/files\/d1b3abc745eee1acd06b0f782e44b86eL.jpg?v=1788047404"},{"product_id":"dinan-5mm-wheel-spacers-5x120-72-6mm-bmw-e-f-chassis","title":"Dinan 5mm Wheel Spacers 5x120 72.6mm CB (Set of 2) - BMW E and F Chassis","description":"\u003cp\u003eFive millimeters sounds like nothing. Then you look at your car from behind and see the wheels sitting a little too far inside the fenders, or a new brake kit needs just a bit more caliper clearance. That is exactly the gap a 5mm spacer closes.\u003c\/p\u003e\n\u003cp\u003eDinan 5mm Wheel Spacers move each wheel 5mm further out from the hub on BMW E and F chassis cars with the 5x120 bolt pattern and 72.6mm center bore. They are CNC-machined from 6061 aluminum, finished in anodized black, and sold as a set of 2 to do one axle.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhy Dinan 5mm Wheel Spacers\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eFive millimeters is the subtle option. It pulls the wheel just far enough to tidy up the stance or clear a caliper without changing the character of the car. The 72.6mm center bore matches the BMW hub, so the spacer locates on the hub the way your wheel does. Dinan machines each one from 6061 aluminum with a weight saving design, then anodizes it black so it disappears behind the spokes.\u003c\/p\u003e\n\u003cp\u003eTwo things to know before you order. First, you need longer lug bolts. Your factory bolts will not reach through a 5mm spacer with enough thread engagement, so buy the correct Dinan bolts with the spacers (listed below). Second, check which bolt pattern your car uses. Dinan groups fitment by chassis family, and some F-chassis cars use the G-chassis 5x112 spacer instead. Dinan part number D210-2035. Sold by AutoTecknic, an authorized Dinan dealer.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhat's Included\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e2 Dinan 5mm wheel spacers, 5x120, 72.6mm center bore\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eLug bolts are not included and are sold separately.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eKey Features\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e5mm thickness per spacer\u003c\/li\u003e\n  \u003cli\u003e5x120 bolt pattern with 72.6mm center bore\u003c\/li\u003e\n  \u003cli\u003eCNC-machined 6061 aluminum\u003c\/li\u003e\n  \u003cli\u003eWeight saving design\u003c\/li\u003e\n  \u003cli\u003eAnodized black finish\u003c\/li\u003e\n  \u003cli\u003eSet of 2, one axle\u003c\/li\u003e\n  \u003cli\u003eDinan suggested bolts: D220-0010 (M12x1.5 cone seat, 32mm) for E chassis, D220-0003 (M14x1.25 cone seat, 33mm) for F chassis\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eVehicle Fitment\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eFits BMW models by chassis family, as published by Dinan:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eBMW E chassis with 5x120 bolt pattern (M12x1.5 lug bolts)\u003c\/li\u003e\n  \u003cli\u003eBMW F chassis with 5x120 bolt pattern (M14x1.25 lug bolts)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eExceptions apply. Dinan lists the F9x M5 \/ M8 and the F48 X1 \/ F39 X2 as exceptions: they use the G chassis spacer fitment (5x112, M14x1.25 bolts) and need a different spacer. G chassis cars are not covered by this part. If you are not sure which pattern your car uses, contact us with your VIN before ordering.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eInstallation Notes\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eAny DIYer who can change a wheel can fit these. Use a torque wrench, and always use the correct longer bolts.\u003c\/p\u003e\n\u003col\u003e\n  \u003cli\u003eLoosen the lug bolts, raise the car safely and remove the wheel.\u003c\/li\u003e\n  \u003cli\u003eClean any rust or debris from the hub face so the spacer sits flat.\u003c\/li\u003e\n  \u003cli\u003eSlide the spacer over the hub and line up the bolt holes.\u003c\/li\u003e\n  \u003cli\u003eRefit the wheel with the longer Dinan lug bolts and snug them in a star pattern.\u003c\/li\u003e\n  \u003cli\u003eLower the car, torque the bolts to the factory specification, and recheck torque after the first 50 to 100 miles.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"Dinan","offers":[{"title":"Default Title","offer_id":51584290259190,"sku":"DNND210-2035","price":52.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2674\/6278\/files\/edad82b19668375ca25c06c32d9e861aL.jpg?v=1788481145"},{"product_id":"dinan-12mm-wheel-spacers-5x120-72-6mm-bmw-e-f-chassis","title":"Dinan 12mm Wheel Spacers 5x120 72.6mm CB (Set of 2) - BMW E and F Chassis","description":"\u003cp\u003eLower a car and the wheels suddenly look lost inside the arches. Twelve millimeters per side is the move that pushes them out to where the fender line says they belong.\u003c\/p\u003e\n\u003cp\u003eDinan 12mm Wheel Spacers move each wheel 12mm further out from the hub on BMW E and F chassis cars with the 5x120 bolt pattern and 72.6mm center bore. They are CNC-machined from 6061 aluminum, finished in anodized black, and sold as a set of 2 to do one axle.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhy Dinan 12mm Wheel Spacers\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eTwelve millimeters is a real stance change. It moves the wheel well out toward the fender lip, so check your tire-to-fender clearance at full compression before you commit. The 72.6mm center bore matches the BMW hub, so the spacer locates on the hub the way your wheel does. Dinan machines each one from 6061 aluminum with a weight saving design, then anodizes it black so it disappears behind the spokes.\u003c\/p\u003e\n\u003cp\u003eTwo things to know before you order. First, you need longer lug bolts. Your factory bolts will not reach through a 12mm spacer with enough thread engagement, so buy the correct Dinan bolts with the spacers (listed below). Second, check which bolt pattern your car uses. Dinan groups fitment by chassis family, and some F-chassis cars use the G-chassis 5x112 spacer instead. Dinan part number D210-2040. Sold by AutoTecknic, an authorized Dinan dealer.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhat's Included\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e2 Dinan 12mm wheel spacers, 5x120, 72.6mm center bore\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eLug bolts are not included and are sold separately.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eKey Features\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e12mm thickness per spacer\u003c\/li\u003e\n  \u003cli\u003e5x120 bolt pattern with 72.6mm center bore\u003c\/li\u003e\n  \u003cli\u003eCNC-machined 6061 aluminum\u003c\/li\u003e\n  \u003cli\u003eWeight saving design\u003c\/li\u003e\n  \u003cli\u003eAnodized black finish\u003c\/li\u003e\n  \u003cli\u003eSet of 2, one axle\u003c\/li\u003e\n  \u003cli\u003eDinan suggested bolts: D220-0012 (M12x1.5 cone seat, 39mm) for E chassis, D220-0005 (M14x1.25 cone seat, 40mm) for F chassis\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eVehicle Fitment\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eFits BMW models by chassis family, as published by Dinan:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eBMW E chassis with 5x120 bolt pattern (M12x1.5 lug bolts)\u003c\/li\u003e\n  \u003cli\u003eBMW F chassis with 5x120 bolt pattern (M14x1.25 lug bolts)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eExceptions apply. Dinan lists the F9x M5 \/ M8 and the F48 X1 \/ F39 X2 as exceptions: they use the G chassis spacer fitment (5x112, M14x1.25 bolts) and need a different spacer. G chassis cars are not covered by this part. If you are not sure which pattern your car uses, contact us with your VIN before ordering.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eInstallation Notes\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eAny DIYer who can change a wheel can fit these. Use a torque wrench, and always use the correct longer bolts.\u003c\/p\u003e\n\u003col\u003e\n  \u003cli\u003eLoosen the lug bolts, raise the car safely and remove the wheel.\u003c\/li\u003e\n  \u003cli\u003eClean any rust or debris from the hub face so the spacer sits flat.\u003c\/li\u003e\n  \u003cli\u003eSlide the spacer over the hub and line up the bolt holes.\u003c\/li\u003e\n  \u003cli\u003eRefit the wheel with the longer Dinan lug bolts and snug them in a star pattern.\u003c\/li\u003e\n  \u003cli\u003eLower the car, torque the bolts to the factory specification, and recheck torque after the first 50 to 100 miles.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"Dinan","offers":[{"title":"Default Title","offer_id":51606435791094,"sku":"DNND210-2040","price":76.95,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2674\/6278\/files\/bcee50c015eea439a19c3e1466f815d1L.jpg?v=1789001883"},{"product_id":"dinan-6mm-wheel-spacers-5x120-72-6mm-bmw-e-f-chassis","title":"Dinan 6mm Wheel Spacers 5x120 72.6mm CB (Set of 2) - BMW E and F Chassis","description":"\u003cp\u003eYour wheels look great until you see them from behind, tucked a few millimeters too far inside the fenders. Or a big brake upgrade leaves the caliper kissing a spoke. Six millimeters per side is often all it takes to fix both.\u003c\/p\u003e\n\u003cp\u003eDinan 6mm Wheel Spacers move each wheel 6mm further out from the hub on BMW E and F chassis cars with the 5x120 bolt pattern and 72.6mm center bore. They are CNC-machined from 6061 aluminum, finished in anodized black, and sold as a set of 2 to do one axle.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhy Dinan 6mm Wheel Spacers\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eSix millimeters is a small, clean step. It fills the wheel well a touch and opens up caliper clearance without pushing the tire toward the fender lip. The 72.6mm center bore matches the BMW hub, so the spacer locates on the hub the way your wheel does. Dinan machines each one from 6061 aluminum with a weight saving design, then anodizes it black so it disappears behind the spokes.\u003c\/p\u003e\n\u003cp\u003eTwo things to know before you order. First, you need longer lug bolts. Your factory bolts will not reach through a 6mm spacer with enough thread engagement, so buy the correct Dinan bolts with the spacers (listed below). Second, check which bolt pattern your car uses. Dinan groups fitment by chassis family, and some F-chassis cars use the G-chassis 5x112 spacer instead. Dinan part number D210-2036. Sold by AutoTecknic, an authorized Dinan dealer.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhat's Included\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e2 Dinan 6mm wheel spacers, 5x120, 72.6mm center bore\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eLug bolts are not included and are sold separately.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eKey Features\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e6mm thickness per spacer\u003c\/li\u003e\n  \u003cli\u003e5x120 bolt pattern with 72.6mm center bore\u003c\/li\u003e\n  \u003cli\u003eCNC-machined 6061 aluminum\u003c\/li\u003e\n  \u003cli\u003eWeight saving design\u003c\/li\u003e\n  \u003cli\u003eAnodized black finish\u003c\/li\u003e\n  \u003cli\u003eSet of 2, one axle\u003c\/li\u003e\n  \u003cli\u003eDinan suggested bolts: D220-0011 (M12x1.5 cone seat, 35mm) for E chassis, D220-0004 (M14x1.25 cone seat, 35mm) for F chassis\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eVehicle Fitment\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eFits BMW models by chassis family, as published by Dinan:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eBMW E chassis with 5x120 bolt pattern (M12x1.5 lug bolts)\u003c\/li\u003e\n  \u003cli\u003eBMW F chassis with 5x120 bolt pattern (M14x1.25 lug bolts)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eExceptions apply. Dinan lists the F9x M5 \/ M8 and the F48 X1 \/ F39 X2 as exceptions: they use the G chassis spacer fitment (5x112, M14x1.25 bolts) and need a different spacer. G chassis cars are not covered by this part. If you are not sure which pattern your car uses, contact us with your VIN before ordering.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eInstallation Notes\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eAny DIYer who can change a wheel can fit these. Use a torque wrench, and always use the correct longer bolts.\u003c\/p\u003e\n\u003col\u003e\n  \u003cli\u003eLoosen the lug bolts, raise the car safely and remove the wheel.\u003c\/li\u003e\n  \u003cli\u003eClean any rust or debris from the hub face so the spacer sits flat.\u003c\/li\u003e\n  \u003cli\u003eSlide the spacer over the hub and line up the bolt holes.\u003c\/li\u003e\n  \u003cli\u003eRefit the wheel with the longer Dinan lug bolts and snug them in a star pattern.\u003c\/li\u003e\n  \u003cli\u003eLower the car, torque the bolts to the factory specification, and recheck torque after the first 50 to 100 miles.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"Dinan","offers":[{"title":"Default Title","offer_id":51622185468150,"sku":"DNND210-2036","price":52.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2674\/6278\/files\/209f0a153b2d93c3e4ab8b3319273c06L.jpg?v=1789262840"}],"url":"https:\/\/autotecknic.com\/collections\/dinan-wheel-spacers.oembed","provider":"AutoTecknic USA","version":"1.0","type":"link"}